Masonry repair
Sweep & inspection
Caps & crowns
Flue relining
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Famco Chimney Repair in Henderson: What to Know First
We repair Famco chimney components in Henderson regularly, and most jobs are done in one visit. A typical Famco anchor plate repair or flashing replacement runs $285 to $640, while full chase cover replacement lands between $800 and $1,600 depending on size and material. Every repair gets a written price before we start, and every repair carries our 365-Day Done Right Promise in writing.
This page is for Henderson homeowners with a Famco chimney system, whether you know the exact model or just recognize the name on your chase cover, anchor plate, or termination cap. If you’re seeing water stains on the ceiling near the chimney, rust streaks on the chase, or loose brick at the crown line, call (775) 375-4267. We’ll send a background-checked technician who knows Famco parts by sight.
How Famco Products Fail – and How We Fix Them
- Famco anchor plates rust at the bolt holes first. The galvanized steel base plate that secures the flue pipe to the top of the fireplace is the most common Famco failure we see in Henderson. Moisture collects at the four bolt points, rust creeps in, and the plate starts to warp or crack. We remove the old anchor plate, install a new Famco or equal-gauge replacement, and seal the joint with high-temp silicone rated for continuous 500°F exposure.
- Famco locking bands slip on tall chase runs. The band that locks sections of chimney pipe together can work loose over years of wind vibration, especially on two-story chases in the Green Valley Ranch and Anthem areas where the wind comes off Black Mountain. We retorque or replace the band, then verify the pipe joints are still flush before we button the chase back up.
- Famco termination caps clog with desert dust and creosote mix. The standard Famco cap has a mesh screen that Henderson’s fine dust loads up faster than most people expect. When the screen gets even 40 percent blocked, draft drops and smoke starts rolling back into the house. We clean the screen, and if the mesh is warped from heat, we replace the cap with a Famco or Copperfield unit.
- Famco chase pans fail at the welded corners. The galvanized pan that sits under the cap and sheds water off the top of a wood-framed chase will rust through at the seam welds, usually inside ten years in our climate. Once water gets past the pan, it rots the chase framing and you’ve got a much larger repair. We fabricate and install stainless steel replacement pans in-house, not thin galvanized stock.
- Famco storm collars crack from UV and heat cycling. The collar that seals where the pipe exits the chase top takes direct sun all day in Henderson. The neoprene collar gets brittle, splits, and lets rain run straight down the pipe. We replace it with a new storm collar and high-temp caulk bead, and we check it as part of every sweep.
Styles & brands we work with
Our Famco Chimney Repair Process
- 1
Call or schedule online. A live person answers the phone at (775) 375-4267. We get your address, the symptom you’re seeing, and whether you know what Famco part you have. If you don’t know, that’s fine.
- 2
On-site inspection. The technician gets on the roof or into the chase, identifies the failing Famco part, and takes photos. You see the photos. Nothing gets recommended that you can’t see with your own eyes.
- 3
Parts decision. If a genuine Famco part is available and it’s the best call for the job, we spec it. If the aftermarket version from Olympia Chimney or Copperfield does the same job with a better material or a better price, we tell you that and you choose. We don’t push OEM just because the name matches.
- 4
Repair in writing. You get a written price for the exact repair, parts included, before any work starts. The number on that paper is the number on the invoice. No add-ons, no surprise line items.
- 5
The work and the test. We make the repair, then run the flue to confirm draft and seal. If it’s a water-related fix, we check for residual moisture and document the condition of the surrounding materials.
- 6
Cleanup and guarantee. The site is clean before we leave. You get a written 365-Day Done Right Promise. If the covered repair fails within that year, we return at no charge. No arguments, no re-inspection fee.
See the difference
Before
After
Before
After
Before
AfterWhat Famco Chimney Repair Costs in Henderson
Here are the ballpark numbers we quote most often for Famco work in Henderson. These are fully loaded prices: parts, labor, cleanup, and the written guarantee.
- Anchor plate replacement: $285 to $420
- Storm collar replacement: $180 to $260
- Termination cap replacement (screen or full cap): $240 to $480
- Locking band repair or replacement: $150 to $300
- Chase pan replacement (stainless steel, fabricated to fit): $800 to $1,600
- Flashing repair at the roofline: $400 to $850
What moves the price is access. A one-story ranch with a walkable roof is a different job than a two-story chase in Green Valley Ranch that needs a 32-foot ladder and two techs. Material condition matters too. If the flue pipe itself is rusted through, we’ll tell you what can safely wait and what can’t. Call (775) 375-4267 for an exact written estimate. It costs nothing to have us look.
Why Henderson Homeowners Call Flint Chimney Co Henderson for Famco Work
We’re an independent Famco service provider, not an authorized warranty station. That means when we tell you a part needs replacing, we’re not reading from a manufacturer script. We’re looking at the part, telling you what we see, and giving you options. Hank Delano grew up in Los Angeles and learned the trade at LA Trade-Technical College before spending two decades putting that education to work. He and our crew have worked on Famco systems all over Henderson, including a stretch of Green Valley Ranch homes where Famco anchor plates from the early 2000s are failing at about the same rate.
We also work with DuraFlex liners, HeatShield resurfacing systems, and Gelco products, so if your Famco repair exposes a flue issue that needs a different material, we can handle it without bouncing you to another company. Every repair carries our 365-Day Done Right Promise in writing. If a covered repair fails within a year, the return visit is free. Like Hank says: “Tell me what the flue looks like, and I’ll tell you what it costs – no guessing, no padding.”
FAQs
We’re an independent Famco service provider, so we don’t file warranty claims and we can’t speak for Famco’s coverage. That said, for chimneys that are past their warranty period, which is most of what we see in Henderson, our repair work carries its own written one-year guarantee. If you’re inside the Famco warranty window, talk to us before you pay for anything. Sometimes the right move is a warranty claim, and we’ll tell you that plainly if it’s true.
Common parts like anchor plates, storm collars, and termination caps are usually on our truck or at our supplier same week. Chase pans are fabricated to your chase dimensions, which typically adds three to five days. If your chimney is actively leaking into the house, we’ll install a temporary cover at no additional labor charge while the fabrication happens. Call (775) 375-4267 and we’ll tell you what the parts timeline looks like for your specific model.
As long as the flue liner is sound and the chimney structure is stable, repair makes sense. We’d only recommend replacement when the liner is cracked, the pipe sections have separated beyond repair, or the chase framing has rotted from water intrusion. The repair costs on this page are what we’d quote to keep a healthy Famco system working. If replacement is the honest answer, we’ll show you the photos and the numbers and you make the call.
The specific damage depends on which part is failing. A rusted anchor plate can let exhaust gases leak into the chase cavity instead of up the flue. A cracked storm collar or failed chase pan lets water run down the pipe and into the house framing. A blocked termination cap forces smoke back into the room. None of these get better on their own, and the water-related ones get noticeably more expensive every year. Call (775) 375-4267 to schedule an inspection and get the exact scope in writing.
We repair and replace the full range of Famco chimney components: anchor plates, locking bands, storm collars, termination caps, chase pans, and the flashing where the chase meets the roof. If the issue turns out to be in the flue liner itself, we install and service DuraFlex, HeatShield, and Gelco systems, which is often more cost-effective than rebuilding the chase. Bring us the symptom and we’ll tell you what you’re actually dealing with.
Written by Hank Delano, Owner, Flint Chimney Co Henderson at Flint Chimney Co Henderson, serving Henderson and nearby areas.