Masonry repair
Sweep & inspection
Caps & crowns
Flue relining
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Olympia Chimney Chimney Repair in Henderson: What to Know First
Olympia Chimney chimney repair in Henderson typically runs $350 to $2,800 depending on whether we’re repointing mortar joints, rebuilding a spalled brick crown, or relining a flue with HeatShield or DuraFlex. Most repairs are completed in a single visit, and we work on Olympia Chimney stainless liners, caps, and masonry components as an independent Olympia Chimney service provider, not a manufacturer-authorized dealer. You get a written price before any work begins, and that price is the price on the invoice. If you own a home in Henderson with an Olympia Chimney system and you’re seeing rust stains, flaking brick, or water in the firebox, call (775) 375-4267 for a straight answer and a free estimate.
How Olympia Chimney Products Fail – and How We Fix Them
- Rusted stainless caps on Olympia Chimney LD and RG series systems. Henderson’s dry heat is easy on caps compared to coastal climates, but our monsoon-season downpours and hard water from Lake Mead accelerate rust at the spot welds on Olympia’s standard stainless caps. We cut out the failed cap, install a Gelco or Olympia-brand replacement with marine-grade fasteners, and seal the chase top so water can’t pond around the cap base.
- Mortar joint erosion at the crown-to-brick transition. In Henderson’s Green Valley Ranch and Anthem neighborhoods, older Olympia Chimney installations from the early 2000s are now showing crown hairline cracks. This is a known pattern: the factory crown mortar on that vintage dries out and separates from the brick, especially on west-facing chimneys that get full afternoon sun. We grind out the failing joints and repoint with a mortar matched to the brick’s absorption rate, so the repair doesn’t spall the surrounding masonry within a few seasons.
- Chase pan screw-together seams leaking around the flue collar. Olympia Chimney galvanized chase pans are workable, but the seam where the pan meets the flue collar takes a beating from Henderson’s 60-degree winter-to-summer temperature swings. You’ll see water staining on the ceiling below the chase, often misdiagnosed as a flashing problem. We reseal the collar with urethane sealant, replace the pan if the rust is through, and write down what we saw so you’re never guessing.
- Spalling brick on knee-wall and load-bearing chimneys. Brick chimneys built with Olympia Chimney clay flue tile and standard modular brick will spall when water enters through a failing cap and then freezes in the brick face during those rare but real Henderson winter nights when temps drop below 32°F. We cut out the spalled brick, replace with matched brick or standard modular in a complementary color, and waterproof the repair with a breathable siloxane sealer so water beads off instead of soaking in.
- Warped or seized damper assemblies on Olympia Chimney top-sealing dampers. The cable and spring tension on Olympia’s top-seal damper design weakens with repeated use. On Henderson homes with outdoor ash pits or frequently used fireplaces, we see the cable kink at the pivot point. We rebuild the damper assembly using Olympia-brand parts when available, or install a Copperfield or Gelco top-mount damper as a straight-swap replacement with the same footprint.
Styles & brands we work with
Our Olympia Chimney Chimney Repair Process
- 1
Call and schedule. A live person answers at (775) 375-4267. We book a window that works, and we show up inside that window. If we’re running behind, you’ll know before the window starts.
- 2
On-site inspection and diagnosis. Our technician gets on the roof and looks at the full chimney: crown, cap, mortar, brick, flashing, and the accessible flue. We use a camera when the problem is inside the flue. You see what we see, either from the roof photo report or the live camera feed we can run on the tablet.
- 3
Written price before work begins. We hand you a line-item price. It covers materials, labor, and any masonry disposal. You approve that number or we don’t do the work. There is no “found damage” surprise once tools come off the truck because we look before we quote.
- 4
Parts decision: OEM or quality aftermarket, stated plainly. If your Olympia Chimney cap or damper needs replacing, we’ll tell you whether the Olympia-brand part is the right call, or whether a Gelco, Copperfield, or Famco equivalent will outlast it for less money. When we use aftermarket, we say so on the invoice.
- 5
The repair itself. Repointing, crown rebuild, flashing reseal, waterproofing, or cap replacement. We protect the work area, clean up every scrap, and leave the site the way we found it, which means no mortar crumbs on your patio furniture.
- 6
Final walkthrough and the 365-Day Done Right Promise. We walk you through what we did, show you the finished work, and hand you a written guarantee valid for one full year from the service date. If a covered repair fails in that window, we return at no charge. No argument, no fine print.
See the difference
Before
After
Before
After
Before
AfterWhat Olympia Chimney Chimney Repair Costs in Henderson
Here’s what we typically see on Olympia Chimney repairs in Henderson:
- Chase pan reseal or sealing around the flue collar: $300 to $550
- Cap replacement (Gelco or Olympia-brand stainless): $250 to $600 installed
- Mortar repointing of a standard chimney stack: $800 to $1,800 depending on height and joint depth
- Crown rebuild or crown patch with proper expansion joint: $600 to $1,400
- Full chimney rebuild (partial teardown and re-set of brick above the roofline): $3,000 to $8,000 plus access equipment if the roof pitch is too steep for ladders
- Flue relining (HeatShield or DuraFlex stainless, not a patch job): $2,500 to $6,000 depending on flue length and liner diameter
What moves the price: roof access, how many stories, how much brick needs to be cut out, and whether the existing chase is repairable or a full replacement. We give you a written range on the phone after we hear what you’re seeing, and the exact number before a tool comes off the truck. Call (775) 375-4267 for a free estimate.
Why Henderson Homeowners Call Flint Chimney Co Henderson for Olympia Chimney Work
Hank Delano and our crew work on Olympia Chimney systems the way we work on everything else: we tell you what the flue looks like, we write down the price, and we stand behind it. The 365-Day Done Right Promise means a full year of coverage on every repair, with a free return visit if anything we fixed fails within that year. Our techs are background-checked and uniformed, and they’ve been inside enough Olympia Chimney chases in Henderson to know the brand’s failure points without needing a phone call to anyone. When a job calls for a part outside the Olympia Chimney catalog, we work with DuraFlex, HeatShield, and Gelco components and name them on the invoice so you know exactly what’s in your chimney. We’ve been serving Henderson since 2002 as part of the Garrison Partners family, which means the same written-price, written-guarantee standard applies whether you’re in Green Valley Ranch, MacDonald Highlands, or over by Lake Las Vegas.
FAQs
Working with an independent repair company does not automatically void a manufacturer’s warranty, as long as the repair is performed correctly and with compatible materials. That is the standard we work to. As an independent Olympia Chimney service provider, we follow the manufacturer’s installation and repair specs, and we document the work. If you have an active warranty, we recommend you check the terms before we start, and we’ll help you understand what’s covered.
Most common repairs like cap replacement, chase pan resealing, and mortar repointing can be scheduled within 5 to 10 business days of your call, and the work itself is usually done in one visit. Full chimney rebuilds or flue relining take longer because of the tear-out and cure time. Call (775) 375-4267 and give us the basic symptoms, and we’ll tell you what window we’re working with.
Both, and we’ll tell you which is going on your chimney before the work starts. When an Olympia-brand cap or damper is the best fit and available, we use it. When a Gelco, Copperfield, or Famco part will outlast the OEM part at a better price, we say so and put it in writing. The brand we care most about is the one that keeps water out of your house for the next decade.
If the brick above the roofline is spalling in more than a few spots, if the flue liner is cracked in multiple places, or if the crown has separated from the brick face, replacement is usually the better money. If it’s a cap, a patch of mortar, or flashing, repair is almost always the right call. We won’t sell you a rebuild you don’t need, and we won’t patch a chimney that’s past saving. Hank’s rule: “Tell me what the flue looks like, and I’ll tell you what it costs – no guessing, no padding.”
Water keeps getting in. In Henderson, that means mortar joints widen, brick spalls, and over enough monsoon seasons you go from a $900 repointing job to a $7,000 rebuild. If there’s a failing flue liner, you’re also looking at a potential house fire or carbon monoxide entering the living space. The repair is always cheaper on the front end. Call (775) 375-4267 for a free estimate, and we’ll tell you plainly what can wait and what can’t.
Written by Hank Delano, Owner, Flint Chimney Co Henderson at Flint Chimney Co Henderson, serving Henderson and nearby areas.